Magic Jack is a voice over IP system, or VOIP, that is connected to a computer via a USB port. It When you want to set up a two line system with one line connected to the Magic More Articles. How to Hook Up a Fax to Comcast Phone Lines How to Connect More Than One Phone to a Magic Jack ยท How to Connect an.
Table of contents
- Video of the Day
- How to Connect More Than One Phone to a Magic Jack
- Customer Questions & Answers
- How to Connect More Than One Phone to a Magic Jack | It Still Works
Video of the Day
The opposite end of the telephone splitter cable has two female ends. Plug each of the opposite ends of the telephone cables into the "In" port on the side of the telephone. Greyson Ferguson is a graduate of the Savannah College of Art and Design with a degree in film and television. He currently resides in Lansing, Michigan where he works on independent film projects and writes for numerous publications. Ferguson primarily focuses on computer and electronic articles.
Connect a telephone cable into each one of the free female ends on the splitter cable.
Making all of your phones cordless is likely the easiest thing to do but it should be fine with your current setup, so long as disconnected at NID. It is just Internet traffic and they distinguish each other by the port e. I live in a 10 storey apartment building which is 30 years old. I want to get voip and since the building uses Bell cables I have been told I must get a dry loop. The problem is that my computer equipment must stay in a specific room although I have 5 other phone jacks in the apartment.
- .
- argumentative research paper on online dating.
- great expectations dating services south university drive fort worth tx.
At present I have Bell service and my main phone is connected in the computer room with 4 satellite phones spread through the apartment. I have been told 2 things. When they put in the dry loop in I may only be able to use one jack for the phone. Others say that all jacks can all be used. Everyone says they can't tell me if I will be able to use the jack in my computer room.
What has been your experience. The internet provider orders the installer to put in the dry loop but say they cannot ask them to come to the apartment to be sure the proper jack is working. The Voip service only sells the product and doesn't have anything to do with the installation and the Bell Installer that I talked to while he was working on another repair in the building couldn't tell me how to have the installation done correctly or even who to phone to have it done even if I was willing to pay for the extra service myself.
- stove hook up.
- WhichVoIP Visitor Comments.
- How do I Add Multiple Phones with VoIP | WhichVoIP!
- Ask us your question or add a comment:.
Do you have any suggestions of what to do. So long as you have Internet, VoIP has a chance. The test will verify that you are capable of running VoIP on your Internet. You won't need to use ANY phone jack in your apartment if you go down this path. Does this make sense?
- interesting dating profile.
- durgapur dating.
- best way to hook up with a guy.
- How to Use Two Phone Lines With Magic Jack | It Still Works!
- !
- How do I Add Multiple Phones with VoIP.
I have two 2 or three 3 MagicJack modules. Can I simply plug each of them into my network behind the firewall and use a different phone on each module?

Of course your firewall has to be able to handle this i. Presumably you need 3 different phone numbers and this is why you are doing this, yes? I say this as it sounds painful to have a different phone hanging off each MJ. I don't know your requirements but one idea that comes to mind if your call volume is relatively light is to buy one IP phone that has 3 lines and configure each line for a different phone number and route them straight to a trunking provider.
I say this as I wrote an article on this some time ago and it seems it might be of interest if you want everything to go through 1 phone instead of 3. Wish I'd found this article before. Join over , other WhichVoIP visitors who receive useful tips, special promotions and valuable insights. One simple method is by using a multiple jack extension connector.
How to Connect More Than One Phone to a Magic Jack
However, the limitation with this is that the phone connections are still at the location of your ATA device. This is a simple solution but not very flexible if you want to distribute your phones throughout your home. Digital cordless phone systems are a great option for distributing your VoIP throughout your home. Digital cordless phone systems are commonplace in homes these days with MHz, 2. They are also very low cost and can be picked up at places such as Costco and can usually be expanded later should you need additional phones. The additional cordless also sometimes referred to as wireless handsets can then be placed anywhere in your home, distributing your phone service to wherever you need it.
Customer Questions & Answers
The great thing about this option is that if you already have cordless phones then you are ready to go and do not need to buy any additional hardware. A variation on the cordless phone idea is to use wireless phone jacks. A base unit connects directly to your ATA. Then, wireless jacks can be used that plug into your household electrical outlets in the locations where you want your additional phones. You can then connect each of your additional phones to a wireless jack and voila, you have your phone service available anywhere in your home that you want it.
How to Connect More Than One Phone to a Magic Jack | It Still Works
However, this option does not seem to be very popular, likely because of the low prices found on cordless phone systems these days. Many people have used their existing telephone wiring and telephone extensions in their home to distribute VoIP throughout the home. It is also used to power your phone and because the line is always live, it means you can make calls even during power outages. These voltages can potentially damage your VoIP equipment if you are not careful. Also, be aware that this voltage is present on the lines EVEN if you no longer have a landline phone service.
The way people have avoided this is to disconnect their landline phone wiring at the Demarcation Point in their Network Interface Device NID, typically a grey or black box located on the outside of your house. Once the existing phone line to the home has been disconnected, the VoIP ATA phone line can be plugged directly into one of the existing phone extensions inside the home.
This will then distribute VoIP to all other phone extensions in the home that are wired to that phone extension. You can then plug your phones in anywhere you have a phone jack in your home. If you decide to do this it is highly recommended that you seek advice from an electrician or someone who is familiar with internal telephone wiring. It is also advised that you pre-check the wiring on the phone jacks to make sure you don't have live PSTN voltage on the jacks before connecting them to the ATA.
A simple telephone line tester device can be used for this purpose.